Journal Papers (1999-2023)
- Qiankun Song, Jigou Liu, Marcelo Lobo Heldwein and Stefan Klaß,
Intelligent Closed-Loop Fluxgate Current Sensor Using Digital Proportional–Integral–Derivative Control with Single-Neuron Pre-Optimization, Signals 2025, 6(2), 14; https://doi.org/10.3390/signals6020014
- Q. Song, J.-G. Liu and Y. Liu,
Novel Low-Speed Measuring Method Based on Sine and Square Wave Signals, Metrology 2023, 3, 82-98
- Y. Liu, J.-G. Liu and R. Kennel,
Optimization of the Processing Time of Cross-Correlation Spectra for Frequency Measurements of Noisy Signals, Metrology 2022, 2, 293-310
- Peiliang Liu, Jigou Liu, Ulrich Westenthanner,
A Fine Modified Calculation Model with Experimental Verification for the Holding Force of the Permanent Magnet, Journal of Magnetics 27(3), 1-7 (2022)
- Y. Liu, J.-G. Liu and R. Kennel,
Frequency Measurement Method of Signals with Low Signal-to-Noise-Ratio Using Cross-Correlation, Machine 2021, 9(6), 123
- Y. Liu, J.-G. Liu and R. Kennel,
Rotational speed measurement using self-mixing interferometry, Applied Optics, Vol. 60, Issue 17, pp. 5074-5080 (2021)
- H. Sun, J.-G. Liu,
A novel algorithm for laser self-mixing sensors used with the Kalman filter to measure displacement, Measurement Science and Technology, Volume 29, Number 7, published 29 May 2018
- H. Sun, J.-G. Liu, Q. Zhang and R. Kennel,
Self-mixing interferometry for rotational speed measurement of servo drives, Applied Optics, Vol. 55, Issue 2, pp236-240 (2016)
- J.-G. Liu and J.-S. Chen, Frequency-selective Adaptive Filtering for Noise Suppression of Discrete Signals, Technisches Messen, in German, tm 11/2003, pp.522-529
- H.C.Schoenekess, W.Ricken, J.-G.Liu, W.J.Becker, Special constructed and optimized eddy current sensors for measuring force and strain in steel reinforced concrete, Sensors and Actuators A, 106 (2003) 159
- J.-G. Liu, Accuracy improvement in computer controlled measuring and test systems, Technisches Messen, in German, tm 9/2002, pp.390-398
- J.-G. Liu, C. Schmidt-Hattenberger, and G. Borm, Dynamic Strain Measurement with a Fibre Bragg Grating Sensor System, Measurement, Vol. 32, no.2, pp. 151-161, September 2002
- J.-G. Liu, Self-correction Algorithms and Applications to Digital Signal Processing, Measurement, Vol. 31, no.2, pp. 107-116, March 2002
- W. Ricken, J.-G. Liu and W.-J. Becker, GMR- and eddy current sensor in the use of stress measurement, Sensors and Actuators A, Vol. 91, pp. 42-45, 2001
- J.-G. Liu; W.-J. Becker; T. Gerhold; W. Ricken: Parameter separation of measuring systems and Sensors by signal processing, Technisches Messen, in German, tm 11/2000, pp. 484-490
- J.-G. Liu and U. Frühauf, Self-Calibration Measuring Methods and Application to Measurements of Electrical Quantities, Measurement, vol. 26, no.2, August 1999, pp. 129-141
- J.-G. Liu, U. Frühauf and A. Schönecker, Accuracy Improvement of Impedance Measurements by Using the Self-Calibration, Measurement, Vol. 25, no. 3, April 1999, pp. 213-225
Journal Papers Before 1990
- J.-G. Liu, Automatic Measuring System of Dual-frequency Laser Interferometer, Electronic Mechanical Engineering, in Chinese, pp. 8-11, No.3, 1987
- J.-G. Liu and S.-X. Duanmu, Measuring Method for Examining the Error of Inductosyn, Machine Tool & Hydraulics, in Chinese, pp.40-45, No.4, 1988
- J.-G. Liu and S.-X. Duanmu: Initial Experiment and Analysis for the Error of Inductosyn in its Range of Installation and Alignment, Journal of Shanghai University of Science and Technology, in Chinese, Vol. 8, No.1, 1986
- J.-G. Liu and S.-X. Duanmu, The summarization of computer aided positioning error compensation & correction, Grinder & Grinding, in Chinese, pp.4-11, No.1, 1987
- J.-G. Liu and S.-X. Duanmu, Method of microcomputer aided positioning error compensation, Chinese Journal of Scientific Instrument, in Chinese, pp.274-279, Vol.8, No.3, 1987
- J.-G. Liu and S.-X. Duanmu, Modelling of positioning error of machine tools, Machine Tool & Hydraulics, in Chinese, pp. 23-32, No.6, 1986
- J.-G. Liu and S.-X. Duanmu: Methods of horizontal sectioning in microcomputer aided error compensation, Shanghai Machine Tool, in Chinese, pp.9-13, No.3, 1986
- J.-G. Liu and S.-X. Duanmu, A research on the positioning error compensation of machine tools by microcomputer, Shanghai Machine Tool, in Chinese, pp.16-20, No.1, 1987
- J.-G. Liu, Microcomputer aided positioning error compensation system, Machine Building Industry Automation, in Chinese, pp.29-34, No.2, 1987
|
